WPoES-8262 Switch 24-port L2 PoE
 

• Isolated Group, Provide Secure for Certain Ports
• 802.1D Compatible & 802.1w Rapid Spanning Tree
• 2 Dual Media for Flexible Fiber Connection
• Broadcast/Multicast/unknown-unicast Storm Control

Introduction

WPoES-8262 supports 24 10/100BASE-T Auto-negotiation
and Auto- MDIX Ethernet ports, and Power over Ethernet
(PoE) to IEEE 802.3af compliant devices. With the 24-port
featuring PoE function, the WPoES-8262 is an ideal
solution for wireless AP, VoIP phones, cameras and PoE
compliance devices in a wide network environment. It’s
fully compliant with the standards of IEEE
802.3/u/x/z/ab/af. It is equipped with 24 UTP (RJ-45) ports
and 2 of which are dual media ports that accommodate
optional 10/100/1000Base-T or SFP modules. In addition,
the switch implements the QoS (Quality of Service), Mac
Filtering Policy, Port Mirror, VLAN and full L2 protocol. The
overall network management is enhanced and the network
efficiency is also improved to accommodate high bandwidth
applications with security.

Benefit

• PoE to Save Your Power Infrastructure Cost
  24 10/100 base-T ports support PoE which allow power (185W) to be supplied to end devices,
  such as Wireless Access Points or VoIP Phones, directly through the existing LAN cables. By
  supplying the power mid-span, you can centralize power distribution and backup without the
  need to increase infrastructure.
• QoS with Four Priority Queues
  The QoS (Quality of Service) feature provides four internal queues to support four different
  classifications of traffic. High priority packet streams experience less delay inside the switch,
  which supports lower latency for certain delay-sensitive traffic. The WPoES-8262 can classify
  the packet as one of the four priorities according to vip port, 802.1p priority tag, DiffServ
  and/or IP TOS. The QoS operate at full wire speed. The actual scheduling at each egress
  port can be based upon a strict priority, weighted round robin or a mix of both.
• Port Mirroring
  This mechanism helps track network errors or abnormal packet transmission without
  interrupting the flow of data. Allow ingress traffic to be monitored by a single port that is
  defined as mirror capture port. The mirror capture port can be any 10/100 port, 10/100/1000
  port. Mirroring multiple ports is possible but can create congestion at the mirror capture port.
• Q-in-Q VLAN for performance & security
  The VLAN feature in the switch offers the benefits of both security and performance. VLAN is
  used to isolate traffic between different users and thus provides better security. Limiting the
  broadcast traffic to within the same VLAN broadcast domain also enhances performance.
  VLAN support enabling advanced techniques such as “802.1Q-in-1Q” to be deployed.
• Isolated Group, Provide Secure for Certain Ports
  The isolated group feature allows certain ports to be designated as protected. All other ports
  are non-isolated. Traffic between isolated group members is blocked. Traffic can only be
  sent from isolated group to non-isolated group.
• 802.1x Access Control Improve Network Security
  802.1x features enable user authentication for each network access attempt. Port security
  features allow you to limit the number of MAC addresses per port in order to control the
  number of stations for each port. Static MAC addresses can be defined for each port to
  ensure only registered machines are allowed to access. By enabling both of these features,
  you can establish an access mechanism based on user and machine identities, as well as
  control the number of access stations.
• 802.1D Compatible & 802.1w Rapid Spanning Tree
  For mission critical environments with multiple switches supporting STP, you can configure
  the switches with a redundant backup bridge path, so transmission and reception of packets
  can be guaranteed in event of any fail-over switch on the network.
• 2 Dual Media for Flexible Fiber Connection
  25, 26 dual media port are provided for flexible fiber connection. You can select to install
  optional transceiver modules in these slots for short, medium or long distance fiber backbone
  attachment. Use of the SFP will disable their corresponding built-in 10/100/1000Base-T
  connections.
• Broadcast/Multicast/unknown-unicast Storm Control
  To limit too many broadcast/multicast/unknown-unicast flooding in the network,
  broadcast/multicast storm control is used to restrict excess traffic. Threshold values are
  available to control the rate limit for each port. Packets are discarded if the count exceeds
  the configured upper threshold.

Application

• The application design for Service / Call Center
• LP-389 with 802.3af PoE-PD compliance
• WPoES-8262 with 802.3af PoE-PSE compliance
• For Supervisor to control and monitor Agent’s status
• Agents using Headset Mode talk and serve incoming calls
• LP-600 and LP-389 support Multiple Programmable Function Keys